
1, Engine Make & Model: Perkins 4008TAG2A
2,Generating Set Model: P1100E1
3,Alternator Model: LL8124B
4, Circuit Breaker Type: 3 Pole ACB
5, Frequency: 50 Hz / 60 Hz
6,Cycle: 4 Stroke
7, Engine Speed: 1500rpm
8, Cooling Method: Turbo, Water/Air cooling
9, Governing Type: Electronic
10, Output Type: AC Three Phase
10, No.of Cylinders/Alignment: 8 / In Line
11,Base Frame Type: Heavy Duty FabriCAT-parts-partsed Steel
Water Cooled Perkins Diesel Generator , 4 Stroke
Output Ratings | |
Generating Set Model | * P1100E1 Prime* Standby* |
380-415V, 50 Hz | 1000.0 kVA 1100.0 kVA 800.0 kW 880.0 kW |
220/127V, 60 Hz | - - - - |
Ratings at 0.8 power factor.
Technical Data | |
Engine Make & Model: | Perkins 4008TAG2A |
Alternator Model: | LL8124B |
Base Frame Type: | Heavy Duty FabriCAT-parts-partsed Steel |
Circuit Breaker Type: | 3 Pole ACB |
Frequency: | 50 Hz 60 Hz |
Engine Speed: RPM | 1500 - |
Fuel Tank Capacity: litres (US gal) | - |
Fuel Consumption: P1000P1 l/hr (US gal/hr) | 215.4 (56.9) - |
Fuel Consumption: P1100E1 l/hr (US gal/hr) | 241.5 (63.8) |
P1000P1 / P1100E1
Engine Technical Data
Physical Data Air System 50 Hz 60 Hz | ||
Manufacturer: Perkins Model: 4008TAG2A No. of Cylinders/Alignment: 8 / In Line Cycle: 4 Stroke Induction: Turbocharged Air To Air Charge Cooled Cooling Method: Water Governing Type: Electronic Governing Class: ISO 8528 G2 Compression Ratio: 13.6:1 Displacement: l (cu.in) 30.6 (1864.9) Bore/Stroke: mm (in) 160.0 (6.3)/190.0 (7.5) Moment of Inertia: kg m² (lb. in²) 15.62 (53376) Engine Electrical System: -Voltage/Ground: 24/Negative -Battery Charger Amps: 40 Weight: kg (lb) - Dry: 3250 (7165) - Wet: 3428 (7557) | Air Filter Type: Replaceable Element Combustion Air Flow: m³/min (cfm) -Standby: 80.5 (2843) - -Prime: 75.0 (2649) - Max. Combustion Air Intake Restriction: kPa (in H2O) 3.7 (14.9) - Radiator Cooling Air Flow: m³/min (cfm) 1152.0 (40683) - External Restriction to Cooling Air Flow: Pa (in H2O) 250 (1.0) - | |
Cooling System 50 Hz 60 Hz | ||
Cooling System Capacity: l (US gal) 180.0 (47.6) - Water Pump Type: Centrifugal Heat Rejected to Water & Lube Oil: kW (Btu/min) -Standby: 349.0 (19847) - -Prime: 332.0 (18881) - Heat Radiation to Room: kW (Btu/min) -Standby: 151.0 (8587) - -Prime: 125.0 (7109) - Radiator Fan Load: kW (hp) 30.0 (40.2) - Cooling system designed to operate in ambient conditions up to 50°C (122°F). | ||
Performance 50 Hz 60 Hz | ||
Engine Speed: RPM 1500 - Gross Engine Power: kW (hp) -Standby: 969.0 (1299.0) - -Prime: 882.0 (1183.0) - BMEP: kPa (psi) -Standby: 2537.0 (367.9) - -Prime: 2309.0 (334.9) - Regenerative Power: kW 80.0 - | ||
LubriCAT-parts-partsion System | ||
Oil Filter Type: Spin-On, Full Flow Total Oil Capacity l (US gal): 166.0 (43.9) Oil Pan l (US gal): 153.0 (40.4) Oil Type: API CG4 15W-40 Cooling Method: Water | ||
Fuel System | ||
Fuel Filter Type: Replaceable Element Recommended Fuel: Class A2 Diesel Fuel Consumption: l/hr (US gal/hr) 110% 100% 75% 50% Load Load Load Load P1000P1 50 Hz 241.5 (63.8) 215.4 (56.9) 157.0 (41.5) 109.4 (28.9) 60 Hz - - - - P1100E1 50 Hz 241.5 (63.8) 173.5 (45.8) 118.0 (31.2) 60 Hz - - - (based on diesel fuel with a specific gravity of 0.85 and conforming to BS2869, Class A2) | ||
Exhaust System 50 Hz 60 Hz | ||
Silencer Type: Level 1 Silencer Model & Qty: SD250 (1) Pressure Drop Across Silencer System: kPa (in Hg) 3.40 (1.004) - Silencer Noise Reduction Level: dB 10 - Max. Allowable Back Pressure: kPa (in. Hg) 8.0 (2.4) - Exhaust Gas Flow: m³/min (cfm) -Standby: 200.0 (7063) - -Prime: 200.0 (7063) - Exhaust Gas Temperature: °C (°F) m³/min (cfm) -Standby: 465 (869) - -Prime: 438 (820) |
P1000P1 / P1100E1
Alternator Performance Data
Data Item | 50 Hz | ||
415/240V | 400/230V | 380/220V | |
Motor Starting Capability* kVA | 2469 | 2301 | 2085 |
Short Circuit Capacity** % | 300 | 300 | 300 |
Reactances: Per Unit Xd X'd X''d | 3.450 0.260 0.141 | 3.720 0.280 0.151 | 4.120 0.310 0.168 |
Reactances shown are applicable to prime ratings
** With optional Permanent Magnet generator or AREP excitation.
Alternator Technical Data
Physical Data Operating Data | |
Manufacturer: FG WILSON | Overspeed: RPM 2250 |
Model: LL8124B | Voltage Regulation (steady state) (%): + /- 0.5 |
No. of Bearings: 1 | Wave Form NEMA = TIF: 50 |
Insulation Class: H | Wave Form IEC = THF: 2.0% |
Winding Pitch Code: 2/3 - 6S | Total Harmonic Content LL/LN: 3.5% |
Wires: 6 | Supression is in line with European Standard Radio Interference: EN61000-6 |
Ingress Protection Rating: IP23 | Radiant Heat: kW (Btu/min) -50 Hz: 51.2 (2912) -60 Hz: - |
Excitation System: AREP | |
AVR Model: R449 |
P1000P1 / P1100E1
Technical Data
3 Phase Ratings and Performance at 50 Hz, 1500 RPM
3 Phase Ratings and Performance at 60 Hz- RPM
Voltage Prime Model Standby Model Voltage Prime Model Standby Model P1000P1 P1100E1 - - | |||||
kVA kW | kVA kW | kVA kW | kVA kW | ||
415/240V | 1000.0 800.0 | 1100.0 880.0 | |||
400/230V | 1000.0 800.0 | 1100.0 880.0 | |||
380/220V | 1000.0 800.0 | 1100.0 880.0 |
Definitions
Standby Rating
These ratings are applicable for supplying continuous electrical power (at variable load) in the event of a utility power failure. No overload is permitted on these ratings. The alternator on this model is peak continuous rated (as defined in ISO 8528-3).
Prime Rating
These ratings are applicable for supplying continuous electrical power (at variable load) in lieu of commercially purchased power. There is no limitation to the annual hours of operation and this model can supply 10% overload power for 1 hour in 12 hours.
Standard Reference Conditions
Note: Standard reference conditions 27°C (80°F) Air Inlet Temp, 152.4m (500ft) A.S.L. 60% relative humidity. Fuel consumption data at full load with diesel fuel with specific gravity of 0.85 and conforming to BS2869: 1998, Class A2.
Weights and Dimensions
General Data
Documents
A full set of operation and maintenance manuals, circuit wiring diagrams, and commissioning/fault finding instruction leaflets.
Generating Set Standards
The equipment meets the following standards: BS5000, ISO 8528, ISO 3046, IEC 60034, VDE 0530, NEMA MG-1.22.
Warranty
All equipment carries full manufacturer's warranty.
Guangdong ALI Testing Equipment Co,.Ltd
Since establishment in 1985, Guangdong ALI Testing Equipment Co., Ltd, a wholly-owned subsidiary of GSKA Group has been providing a wide and complete range of products and services to the society. GSKA has now 16 offices, warehouses and service centres in China, with head office loCAT-partsed in Hong Kong. There are more than 100 employees in GSKA Group, and we are expanding into many industries with rapid expanding pace of China.
There are mainly 4 departments in GSKA Group, namely:
1) Construction and Mining equipment
GSKA has been cooperating with many international famous brands in
China, such as Ingersoll-rand, Atlas Copco and Liebherr. Our
products include concrete batching plants, concrete mixers,
hydraulic crawler drills, pneumatic crawler drills, water well
drills, air compressors, road compactors, breakers and various
other equipment. We are major in several industries, such as
hydro-electric power plants, cement quarries, coal mines and
railway systems.
In order to provide a quick response to our customers, we have stocked over US$1.5 Million spare parts of Ingersoll-rand and Atlas Copco in our Chinese warehouse. Recently, we have exported small air compressors, pneumatic crawler drills, water well drills and drilling accessories and spare parts to overseas market.
2) Power Group
GSKA has been supplying CAT-parts and Broadcrown gensets for more than
15 years. Our major customers include Telecoms, Banks, Airports,
Factories and many other sectors in the society. We are also doing
assembly of gensets in China, under our brand name of "GSKA " with ratings from 1KVA to 2000KVA. The quality of "GSKA " genset has won a very good reputation from customers in China and
overseas market.
We are also the specialists for genuine spare parts, such as CAT-parts, Perkins, FG Wilson, Cummins, , Volvo, etc.
Besides gensets, we also provide total solution on the power problems, such as Powerware - UPS, DC system and battery ,lightning equipment and many other electronic products.
3) Security and IT Group
GSKA acquired famous USA brand name Locktronix in 2004 and started
manufacture electric locks in China. Since then, we have been
exported products to the Middle East, South Asia and Africa. Our
market is expanding each year and we are looking for more
distributors in different countries to be our business partners.
Besides electric locks and accessories, we have also developed our
own access control system by our software team. The system includes
smart card solution and also biometric access control, such as
hand-key, fingerprint and facial recognition. Our EC-PAYROLL system
has been widely used in many factories both in Hong Kong and
mainland China.
After all, GSKA has an objective of "Always Provide the Best" and we shall consistently provide high quality products and reliable services to our worldwide customers. We are looking forward to making good business with our partners