Yaskawa Ac Synchronous Servo Motor 3200W 200V 20.9A AC SERVO MOTOR SGMDH-32A2A-YR13

Yaskawa Ac Synchronous Servo Motor 3200W 200V 20.9A AC SERVO MOTOR SGMDH-32A2A-YR13




Specifications
Manufacturer: Yaskawa
Product number: SGMDH-32A2A-YR13​
Vendor number: SGMDH-32A2A-YR13​
Description: SGMDH-32A2A-YR13​ is an Motors-AC Servo manufactured by Yaskawa
Servomotor Type: SGMDH
Rated Output: 3200W
Power Supply: 200V Standard
Encoder Specifications: 2048 P/R Incremental Encoder
Revision Level: Standard or CE Specification
Shaft Specifications: Straight with keyway
Options: None

OTHER SUPERIOR PRODUCTS

SIMILAR PRODUCTS

Fault output signal (SPDT)
MA/MC: CLOSED during fault condition
MB/MC: OPEN during fault condition
Dry contacts
Contact capacity:
1 A max. at 250Vac
1 A max. at 30Vdc
Analog output signals
FM Multi-function analog output (output frequency)
0 to +10Vdc/100% frequency
Multi-function
analog monitor 1
Function set by H4-01
0 to +10Vdc max. ±5%
2 mA max. AC Analog common –
AM Multi-function analog output (output current) 0 to +10Vdc/100% Drive's rated
output current
Multi-function analog monitor 2
Function set by H4-04 RS-485/ 422 R+ Modbus communication input For 2-wire RS-485, jumper R+ and S+ and jumper R- and S-.
Differential input, R- PHC isolation

Notice

Observe proper electrostatic discharge (ESD) procedures when handling the drive. Failure to comply could result in ESD damage to the drive circuitry. It may be difficult to perform maintenance on the cooling fans of drives installed in a vertical row inside an enclosure. Ensure adequate spacing at the top of the drive to perform cooling fan replacement when required. Operating the motor in the low-speed range diminishes the cooling effects, increases motor temperature, and may lead to motor damage by overheating. Reduce the motor torque in the low-speed range whenever using a standard blower cooled motor. If 100% torque is required continuously at low speed, consider using a special drive or vector motor. Select a motor that is compatible with the required load torque and operating speed range. Do not operate motors above the maximum rated RPM. Failure to comply may lead to bearing or other mechanical motor failures. The speed range for continuous operation differs according to the lubrication method and motor manufacturer. If the motor is to be operated at a speed higher than the rated speed, consult with the manufacturer. Continuously operating an oil-lubricated motor in the low-speed range may result in burning.

Environment Conditions
Installation Area Indoors
Ambient Temperature
-10 °C to +50 °C (IP20/Open-Chassis)
Drive reliability improves in environments without wide temperature fluctuations.
When using an enclosure panel, install a cooling fan or air conditioner in the area to ensure that the air temperature inside
the enclosure does not exceed the specified levels.
Do not allow ice to develop on the drive.
Humidity 95% RH or less and free of condensation
Storage Temperature -20 °C to +60 °C
Surrounding Area
Install the drive in an area free from:
• oil mist and dust
• metal shavings, oil, water or other foreign materials
• radioactive materials
• combustible materials (e.g., wood)
• harmful gases and liquids
• excessive vibration
• chlorides
• direct sunlight
Altitude Up to 1000 meters without derating; up to 3000 meters with output current, ambient temperature, and voltage derating.
Refer to Altitude Derating on page 186 for details.
Vibration 10 to 20 Hz at 9.8 m/s2
20 to 55 Hz at 5.9 m/s2
Orientation Install the drive vertically to maintain maximum cooling effects.

Prevent foreign matter such as metal shavings or wire clippings from falling into the drive during installation and project construction. Failure to comply could result in damage to the drive. Place a temporary cover over the top of the drive during installation. Remove the temporary cover before startup, as the cover will reduce ventilation and cause the drive to overheat.

Shenzhen Wisdomlong Technology CO.,LTD Mainly engaged in automation parts, PLCS,DCS,sensors, relays, dirves,encoder, servo drive,soft starter,touch screen,instrument,process control,electric transmission and factory automation aspects of the project design,software programming,technical service and staff training. Our company locats at the central of China,Shenzhen, Guangdong Province. With rapid development, Wisdomlong serves fields of automation in global markets, Our business covers five continents throughout the world with the basic conviction of honest, the international management of customer-centered concept and purpose of bringing convenience to customers. We have confidence to bring our customers more substantial profit with high-quality service and reasonable prices. Choosing us,you will choose a sincere friend and reliable partner. Please feel free to contact us if you are a global manufacturer of high quality brand products who desires to enter the Chinese market or who searches for a Chinese agent.We would like to create a brilliant future with friends in domestic and overseas. All goods sold have one year warranty.

The company with domestic and international numerous well-known brands supplier to build have extremely good relations of cooperation, in Japan, South Korea, southeast Asia, Africa, Europe and the United States, and formed a stable and efficient supply network. The agent and the products are widely used in machinery, equipment manufacturing, electric power, metallurgy, petrochemical, automobile manufacturing industry, paper making, chemical industry, medicine and aerospace industries.

Our Main Brand:

MITSUBISHI

YASKAWA

PANASONIC

GE FANUC

EMERSON

FISHER-ROSEMOUNT

HONEYWEL

ABB

AB

SHNEIDER MODICON

SIEMENS

................