Flux Cored Welding Wire Machine Automatic Production Line PLC Control

Flux cored welding wire and solid welding Wire Mesh Panel Welding Machine

Main machine of Welded Wire Mesh Machine

Wire dia:0.4mm-2.0mm

Mesh size:12.7mm-50.8mm

Welding width:91.4mm,1219.2mm,1524mm

Working power:380V

50-60HZ

Machine size:

2350×1820×1200mm

Weight: 2.5tons

Welding speed:110 radia

Specifications for your reference:

Description:

Automatic production line for high speed wire welding is through the introduction of Swiss SCHLATTER company technology, after digestion, absorption, and research and development of a device, mainly composed of pay-off stand, wire frame, a longitudinal bar straightening device, longitudinal reinforcement traction device, storage rack, longitudinal reinforcement secondary straightening device, longitudinal reinforcement stepping feeding device, welding host, transverse reinforcement automatic feeding device, shearing machine, mesh network collection device, network transmission of orbit, it is mainly used for concrete road, building, tunnel, subway, water conservancy, such as prefabricated steel fabric in the construction field. This product production efficiency is high, the annual output can reach 50000 tons.

Features:

1. At present, a lot of other domestic products applicable to weld straight bar steel, need to manually wear reinforcement, the intensity of labor is big, the production efficiency is low. This project product is suitable for the plate steel, which can realize continuous welded steel fabric, improved the production efficiency.

2. Adopts two-way 45 ° inclined type straightening machine, straightening effect is good, all straightening roller can be adjusted through a hand wheel, convenient adjustment.

3. Longitudinal reinforcement stepping feeding device is convenient to adjust the longitudinal spacing, suitable for welding for a variety of specifications of the mesh. (patented)

4. Welding host selection for double impact cylinder, cylinder made by the company independent research and development, welding frequency up to 120 times/min, greatly improving the welding efficiency.

5. The transverse reinforcement automatic feeding system, without manual, the system consists of PLC program control, which can realize the continuity of transverse reinforcement accurate feeding.

6. Finished product mesh collecting device is composed of shrinkage, mechanical hand, lift orbits, which can realize the automatic mesh pallet, placed neatly, high production efficiency.

Welding Wire machine parameter

1. Wire material surface pre-treatment

1.1 high shelf pay-off:Put a wire rod, without motor

1.2 Scribble and automatic stop switch: wire out

of the pay-off machine through the steel ring with

a diameter of 200 mm, if a few circle wire

entwined, steel ring that was taken to the other

side, t the bottom of the stroke switch will send

signals, and the entire line emergency stop.

1.3 Repeated bending mechanical shell and

wire ball strong scrubbing device: the wire rod

at least six direction perpendicular(National

initiative)Bending heat treatment to strip iron

oxide on the surface of the wire.

Eight peeling wheel,

material: ZG45 steel, hardness of HRC50, Wheel

inner diameter Ф 115 --- Ф 120mm.

Wheel service life of 6000 hours. After

peeling ,the wire through period of tapered hole, use wire clean ball strongly wipe the

surface of wire rod, and does not damage

the wire surface, reduce the waste into the electrolytic pickling tank, ensure the

effect of pickling, facilitate drawing; By pressure cold water irrigation and block and

impurities, rust on the surface of the wire rod export high-pressure gas blowing

device, reduce by wire out of the water.

• the wire diameter:1.5-2.5mm or 2.5-6mm
• the hole size:20mm(min)
• plc control full automatic
• roll mesh or sheet mesh all is ok

JiangYin YiFa Metal Science & Technology Co., Ltd. is one of the Chinese premier manufacturers of wire drawing machine.We supply advanced wire drawing machine,auxiliary equipment and excellent after-sales service for Chinese and overseas metal products industry. Through 25 years efforts and continuous innovation,

YiFa wire drawing machines,such as straight line wire drawing machine, Bright wire drawing machine ,welding wire machine, inverted vertical wire drawing machine, wire bending machine and other auxiliaries, have the mechanical characteristics structure and electronic control configurations, advanced technical indicators design, stable equipment performance, safe and reliable running and easy operation and maintenance. Machines are widely used with digital control technology and intelligent method, which greatly improves the production efficiency.

https://youtu.be/mucy3xBj4jg

https://youtu.be/dlx7sOr7BIc​

https://youtu.be/QhEkHSrmPRs​

https://youtu.be/KK9hAbfC0hA

https://youtu.be/XUcDPz9q6C4​

https://youtu.be/rLymrsTU8i0​

https://youtu.be/EwnLZa3UvKs​

https://youtu.be/nLrHnO9ZEjE​

https://youtu.be/3NncMTY6Iys​

https://youtu.be/FcHbQIqcPps

https://youtu.be/22cjVkYShR8​

https://youtu.be/hxkYD6VccqM